Everything so far has been about the welfare of the object. This part is about yours. Old furniture can carry live beetles, mold, or paint from the years when paint had lead in it, and a secondhand piece is far easier to turn away at the door than to deal with indoors. Do this pass outside, and stop if it fails.

Deciding what to do

What can hurt you in old furniture, and in the work

Beetles, mold, bed bugs, old paint, solvents and oily rags. A pass that takes twenty minutes in the driveway, done before the piece comes indoors and before any work starts.

Start here Essentials

At minimum this chapter asks you to do one pass, outdoors, before the piece comes in: holes and powder, smell and seams, and the paint question. The beetle families, the regulatory detail and the exposure figures are Go deeper on a first pass.

  1. Do this pass outdoors or in the garage, before the piece comes in. The pass is only useful where its answer can still change something (section 1).
  2. Look for holes and for fresh pale powder, and mark what you find. The powder decides, not the holes (section 2).
  3. Smell it, and look in the seams and folds. A musty odor is the first sign of mold (section 3).
  4. Decide whether it is painted, and whether the paint might be old. Then read the Limits box in section 4.
  5. Tick the hazards pass on your report, line by line. Every line, including the ones you are confident about (your condition report).

Minimum time: about 20 minutes. Done when: your hazards pass is ticked line by line and you have decided whether the piece comes indoors.

1. Why this is a pass, and why it is first Understand

Everything in this chapter is recognition and a stop. The manual tells you how to see an active infestation, lead-era paint, mold or a bed bug, and what to do with the piece then, which is to isolate it, leave it outside, or call somebody. It does not teach fumigation, lead paint removal, mold remediation or stripping, and the reasons are in the sources themselves rather than in caution for its own sake: EPA's own instruction is not to attempt to remove lead-based paint yourself, both extension entomology sources restrict fumigation to licensed operators, and the Park Service's mold guidance is explicit that killing mold does not end the health hazard.

Two structural points about how this is done.

It is a pass, not a search. You do every line, including the ones you are sure about, because the line you skip is the one that mattered. That is why the hazards sheet in your condition report is the same list for everyone, regardless of what you told the setup form.

It comes before the piece comes indoors. This is the part people get wrong, and the cost is high. A pass done in the living room can still tell you there is an active infestation; it cannot stop the infestation arriving in the living room. The American Institute for Conservation's instruction for an actively infested piece is to isolate it immediately in a large sealed plastic bag and call a conservator, or an exterminator familiar with conservation issues, which is a very different operation in a driveway from in a bedroom.

If the piece is already indoors, do the pass anyway. It still tells you what you have, and an active finding is then a reason to move the piece out rather than a reason to panic.

Limits

A pass that finds nothing is not a clearance. It establishes that the things on the list were looked for, by you, with a flashlight, on one day. A dormant infestation outside its emergence season, mold inside a joint, bed bugs in a frame you did not open and lead under a later coat of paint are all consistent with a clear pass.

So "clear" on your report means "nothing found on this date by this method," which is what you actually did. Where the answer matters more than that, because the piece is going into a child's room, because somebody in the house has a respiratory condition, or because you found something and want it identified, the reading to trust comes from an extension entomologist, a licensed pest control operator or a professional who can look at it. Who to hire for furniture work says which, and the recheck in the practice exercise is what turns one day's look into evidence.

2. The pest check

Small round holes in wood are the commonest hazard finding, and the question that matters is not whether there are holes but whether anything is still living in there.

Active or old

University of Kentucky Entomology's extension fact sheet on powderpost beetles gives the test. An active infestation shows powder the color of freshly sawed wood sifting from the exit holes. New holes have not weathered like the wood around them, and in stained wood a new hole shows no stain inside it. Powder that is yellowed, caked, or covered with dust or debris points to old damage.

The complication it also gives: vibration can dislodge powder from old galleries when furniture is moved or jostled, which can look like activity. So the test is not a single look. Mark or seal the existing holes, sweep or vacuum all the powder away, write the date, and look again later.

The timing caveat, and it matters. That same fact sheet says most beetle emergence occurs in spring or summer. So a recheck in November may show nothing and prove nothing. Record the date you swept, record the date you looked again, and if the sweep happened in autumn or winter, say on the report that the recheck is inconclusive until spring. The Ferris chest in section 8 is exactly this case.

The hole sizes, and a conflict between the sources

Hole size narrows the family, which matters because the families behave differently. Here the two extension sources Learn Furniture Care uses do not quite agree, and the honest thing is to show both.

Exit hole sizes as each source gives them
Beetle familyUniversity of Kentucky (ENTFACT-616)Penn State ExtensionNotes from the sources
LyctidRound, "about the size of a pinhead"; no number givenIts page covers Lyctidae and gives "about 1/16 to 1/8 inch in diameter"The two descriptions do not match. Kentucky gives no figure for lyctids; Penn State's figure is the same range Kentucky gives for anobiids
Anobiid1/16 to 1/8 inchNot separately givenKentucky's figure
BostrichidCircular, 1/8 to 1/4 inch; holes made by egg-laying females are free of powderNot separately givenKentucky's figure
Wood-boring beetles generally, in upholstered furnitureThe National Park Service's leaflet on upholstered furniture gives exit or flight holes of 1/16 to 3/16 inchA third range, from a third publisher, covering the group

Convention What to take from that: hole size gets you to a rough group and no further, and anyone who identifies a beetle family from a photograph of holes is going beyond what these sources support. The identification that matters is made by an extension entomologist or a pest control operator who can look at the wood, the holes and ideally a beetle. Record the size you measured and which source's range it falls in, and leave the family open.

Why the family matters

Because re-infestation differs by family, and that is the question behind "will this spread to my house."

Kentucky's fact sheet says lyctids attack only hardwood products such as oak, ash, walnut, hickory, poplar and cherry, that females will not lay eggs where starch is less than about 3 percent, and that infestations can persist in wood with a moisture content as low as about 8 percent. It says emerging lyctids and bostrichids are unlikely to re-infest indoors, because indoor surfaces are finished and starch and moisture decline, and that small numbers may continue to emerge for up to about five years from wood that is becoming unsuitable. Anobiids are the family that can re-infest year after year; their larvae require a 13 to 30 percent wood moisture content.

And the sentence that explains most of what people see: surfaces that are stained, varnished, waxed or painted are immune from attack, in that fact sheet's words, because eggs are laid into unfinished wood. Larvae already inside still emerge through a finish, which is why holes appear in finished furniture, but the finish itself is not where an infestation starts.

That is also why the borate products the same source names work only on bare wood: it says the spray will not penetrate paint, polyurethane or other water-repellent coatings. Penn State says the same, that surface sprays containing borates are not effective on wood that has been varnished, waxed or otherwise sealed.

The lookalike

Before concluding anything, rule out the beetle people most often mistake for a powderpost beetle. Kentucky's fact sheet on the foreign grain beetle describes it as about 1/16 inch long and reddish brown, feeding on the molds and fungi that grow on poorly seasoned lumber or wet plaster and wallboard, and says that beetles in that category do not damage wood. It says the fungi and molds disappear along with the beetles once the moisture source is removed.

What to do with an active finding

Isolate the piece and do not bring it into the house. The AIC instruction is a large sealed plastic bag, immediately, and a call to a conservator or an exterminator familiar with conservation issues. Penn State's instruction on treatment is that only pest control operators licensed to do fumigations may purchase and use those materials, and it adds the point a buyer can use: for an item with numerous holes, demand a receipt from the company that performed the fumigation. It also says fumigation gives no protection against future attack.

3. Mold and bed bugs

Mold

The Park Service's leaflet on mold prevention says that often the first indication of a mold problem is a characteristic musty odor. That is why smelling the inside of every drawer and cupboard is a line on the pass: the nose finds it before the eye does.

What that leaflet establishes, and it changes how people think about the problem:

  • Mold needs moisture to germinate, and without it the spores lie dormant until conditions become favorable. So a dry piece with a history of mold is not an inert piece.
  • Extreme cold, freezing and heat deactivate spores or spore growth but do not kill them, and if temperatures rise afterwards the spores can be reactivated and growth continues.
  • Killing mold does not eliminate all health hazards, and inactive mold may still cause allergic reactions in sensitive people. The leaflet names higher risk for people with respiratory problems, severe allergies, diabetes and compromised immune systems.
  • Cellulose-based materials including wood, and proteinaceous materials including leather, parchment, adhesives and hair cloth, are particularly susceptible, which covers most of what furniture is made of.
  • Its handling instruction for an affected object is to seal it in a polyethylene bag or sheeting to stop spores spreading, and not to touch the mold, because touching spreads the spores. Its protective equipment list for working around mold is a HEPA respirator, goggles, disposable gloves and a washable coat.

The practical consequence for a reader standing beside a musty chest: a musty smell is reason enough to keep the piece out of the house until it is dry and somebody has looked properly, and the fact that the mold is not actively growing today does not settle the health question.

Bed bugs

The Centers for Disease Control and Prevention's page on bed bugs says they spread by getting into the seams and folds of luggage, bags, folded clothes, bedding and furniture, and that how clean a place is does not determine whether they are present. It lists shed exoskeletons and rusty blood spots on mattresses or nearby furniture among the signs, says bed bugs are not known to spread disease, and says to contact a professional pest control company for an infestation.

Two things that page does not say, which matters because they are widely attributed to it. It does not mention secondhand or used furniture specifically, and it gives no heat or cold treatment figures. So Learn Furniture Care does not attribute either to CDC. What the page supports is the inspection: look in the seams, folds and tufting of any upholstery, and look for the signs it names.

4. The paint question

If any part of the piece is painted, this is the section that applies, and it is the one with a federal instruction attached.

EPA's page on reducing lead exposure at home states that in 1978 the federal government banned the sale of lead-based paint for use in homes and childcare facilities. It says homes built before 1978 probably contain it, that about three-quarters of pre-1978 US homes still do, and gives the proportions by era: 24 percent of homes built from 1960 to 1977, 69 percent from 1940 to 1959, and 87 percent before 1940. Those figures are about housing rather than about furniture, and Learn Furniture Care quotes them as what they are, because they are the only era-by-era figures on that page.

What the page says about furniture directly: refinishing old furniture is listed among the jobs and activities that may increase lead exposure.

Lead paint

EPA's instruction, in its own words: "Do not attempt to remove lead-based paint yourself." That is Learn Furniture Care’s line too, in any amount and on any piece.

For damaged painted surfaces, the same page gives the approach: fix damaged areas under 6 square feet without sanding, and wet the area first if you must sand. It also says not to use steel wool, scouring pads, or abrasive or solvent cleaners that may dissolve paint. For paid work that disturbs paint in pre-1978 housing, it requires a lead-safe certified firm under the Renovation, Repair and Painting rule.

On testing: EPA's page says that the Consumer Product Safety Commission does not recommend home lead test kits for use on consumer products. So a negative result from a hardware-store kit is not a basis for deciding to sand something.

There is a separate legal limit that applies to furniture itself, and it is worth knowing because it is often misquoted. The Consumer Product Safety Commission's own page on lead in paint states that all children's products and certain furniture articles must not contain a concentration of lead greater than 0.009 percent, which is 90 parts per million, in paint or any similar surface coating, and that household paint must also meet that requirement. It codifies this at 16 CFR part 1303. The furniture articles it names as covered include beds, bookcases, chairs, chests, tables and dressers; appliances, built-in fixtures and window shades and blinds are not covered.

Physical principle Note what that limit is and is not. It is a limit on what may be sold, so it tells you about furniture manufactured and sold under the rule. It says nothing about what is on a piece made in 1935, and it is not a safe level for a surface you are thinking of sanding.

The practical pass, then, is short: decide whether the piece is painted; decide whether the paint might predate 1978, which on an old piece is usually "possibly" and rarely "no"; note whether any paint is chipping, flaking or chalking and over what area; and decide where a painted piece is going to live and whether children use that room. Those four lines are on the hazards sheet.

5. What the federal rules on strippers currently say

Learn Furniture Care does not teach stripping. It does state where the federal rules stand, because the picture changed recently and most of what is written about it online is now out of date.

As these three EPA pages read on 13 November 2026:

Federal status of two paint-remover solvents, as of 13 November 2026
RuleStatusWhat it covers
The 2019 methylene chloride ruleIn force. EPA's page on it is dated 10 November 2026 and describes it as operative, with no court action mentionedAfter 22 November 2019, manufacturing, processing and distributing methylene chloride for consumer paint and coating removal is prohibited, including distribution to and by retailers and e-commerce sales, which EPA's page puts as such products not being available for purchase by consumers
The 2024 methylene chloride ruleVacated and not in effect. EPA's page, dated 13 November 2026, says the Fifth Circuit vacated it in September 2026 in East Fork Enterprises v. EPA, No. 24-60227, and that regulated entities are not required to comply with its bans, phase-outs or restrictionsIt had finalized broader prohibitions and workplace protections in April 2024. The decision did not affect the 2019 rule or any OSHA requirement or exposure limit
NMP (n-methylpyrrolidone)Proposed only. EPA's page, last updated 29 January 2026, describes a rule announced in June 2024 and speaks of what it would do if finalizedProposed terms include a 45 percent concentration limit in consumer glues and adhesives, container size limits and labeling for other consumer products, a workplace chemical protection program, and commercial bans that would include furniture care products. Docket EPA-HQ-OPPT-2020-0744

Ask the authority This is live litigation, and a date on a manual page is not a substitute for checking. If this decision matters to you, read those three EPA pages yourself rather than relying on the table above, including Learn Furniture Care’s own summary of them. The reason this chapter carries dates on every line is so you can see how old the reading is.

What this means for a reader: the common consumer product that once made stripping easy has been off the consumer market since 2019 under a rule that still stands, the broader 2024 restrictions were vacated in September 2026, and the usual substitute is subject to a proposal that has not been finalized. Combined with the lead instruction above and the fact that stripping is irreversible by definition, that is why Learn Furniture Care explains stripping and does not teach it. Who does it is Who to hire for furniture work.

6. Solvents, and the rags

The hazards in this section are the ones you bring to the piece rather than the ones it brings to you, and they are the likeliest to actually hurt somebody.

Solvents

The Park Service's cleaning leaflet gives the instruction for anyone opening a solvent: follow all safety instructions on the containers, obtain and read the safety data sheets for every solvent used, and ensure ample ventilation throughout the cleaning and drying process. Its waxing leaflet adds a preference, for the weaker organic solvents such as turpentine and mineral spirits over xylene and toluene, which it says can damage some finishes and are more of a health hazard.

For mineral spirits specifically, which is the solvent Learn Furniture Care uses most, the NIOSH Pocket Guide entry for Stoddard solvent gives a flash point of 102 to 110 °F and classes it as a Class II combustible liquid. It lists the exposure routes as inhalation, ingestion and skin and eye contact; the target organs as eyes, skin, respiratory system, central nervous system and kidneys; and symptoms including irritation of eyes, nose and throat, dizziness, dermatitis, and chemical pneumonitis from aspirating the liquid. Its own guidance is to prevent skin contact and prevent eye contact, to wash skin when contaminated, and to remove clothing when wet or contaminated.

The exposure limits it prints are workplace limits rather than household ones, and they are included here as the figures that exist: a NIOSH recommended exposure limit of 350 mg/m³ as a time-weighted average with a ceiling of 1,800 mg/m³ over any 15 minutes, an OSHA permissible exposure limit of 500 ppm, and an IDLH value of 20,000 mg/m³.

The rags

Oily rags

Rags used with oil finishes can catch fire on their own, without a spark or a flame, as the oil cures and generates heat faster than a crumpled pile can shed it.

The National Park Service's fire prevention bulletin on spontaneous combustion names oil-soaked rags among the materials involved, cites an NFPA estimate of 14,070 fires a year, and describes an incident of its own in which rags used with linseed oil on tool handles ignited. Its instruction is to spread soiled rags in a single layer on concrete, out of direct sunlight, with the corners secured so they cannot blow into a pile, and to let them harden before disposal. For businesses it names an OSHA-approved container.

And the instruction for a pile that is already smoking: call 911, and do not disturb it. Spreading a smoking pile out introduces oxygen.

This box appears twice in Learn Furniture Care, here and in Cleaning furniture, waxing it, and reviving a tired finish, where you are actually holding one.

7. Old upholstery

Upholstery is assessed in Learn Furniture Care and not rebuilt, and the hazards in it are worth knowing before anybody lifts a cover.

The Park Service's leaflet on upholstered furniture lists the padding materials historically used: grasses, animal hair, feathers, moss, cotton batting and seaweed, with polyester batting and synthetic foams more recent. It notes that coil springs have been used in upholstered seats since the 1830s. It treats dust as both an abrasive and as an attractant and food source for insects, and says that proteinaceous materials such as silk, horsehair and wool are attacked by dermestids including carpet beetles and clothes moths, whose larvae are repelled by light and feed in dark undisturbed locations, which describes the inside of a chair.

Its own cleaning instruction, for stable show fabric, is to vacuum regularly at low suction and preferably through a nylon mesh window screen of about 18 by 18 inches with protective tape at the edges, using a water-filtering or HEPA vacuum. And its caution: if the fabric is unstable, do not attempt to vacuum, and consult a conservator.

So the pass on an upholstered piece is: look into the seams and folds for bed bug signs, smell it, look for exit holes in the frame where it shows, look for the cast skins and debris of fabric pests, and decide whether the show fabric is sound enough to touch. Opening a piece up to see what is inside is not in Learn Furniture Care; that is Who to hire for furniture work.

Go deeper

The California flame retardant label, and what it tells a secondhand buyer

If you are looking at an upholstered piece made for sale in California since 2015, there may be a label worth reading. Two separate California rules sit behind it, and the distinction between them is the useful part.

The flammability standard Technical Bulletin 117-2013 became effective on 1 January 2014 and was fully implemented on 1 January 2015. The state Bureau of Household Goods and Services, which administers it, says in its own FAQ that under those regulations manufacturers are no longer compelled to make their products open-flame resistant and need only meet the cigarette smoldering resistance tests. It also says plainly that the Bureau does not regulate the use of flame retardant chemicals, and that its flammability standards are performance standards which neither prescribe nor prohibit any specific material or manufacturing method.

The label itself comes from a different law. California Business and Professions Code section 19094, enacted by SB 1019 and effective 1 January 2015, requires a statement on the flammability label of covered products saying whether the upholstery materials contain added flame retardant chemicals, with both options printed and a mark beside the one that applies. The components it covers are the cover fabrics, barrier materials, resilient filling materials and decking materials. Outdoor upholstered furniture and mattresses are outside it.

What a secondhand buyer can take from this: on a covered piece, the label states whether flame retardants were added, which is information no amount of looking will give you. The Bureau says it has no jurisdiction elsewhere and is not aware of the standard or the statement being adopted in other states, so this is a California label rather than a national one, and its absence tells you very little.

The treatment figures, and who can use them

Kentucky's fact sheet gives figures for non-chemical treatment of infested items, and they are included here so that you can recognize what a professional is proposing rather than so that you can do it. For furniture, it says temperatures used for powderpost beetles would be similar to those used for bed bugs, 120 to 135 °F, with exposure up to 24 hours depending on wood thickness. For small items such as carvings and picture frames it gives deep freeze at 0 °F for 3 to 7 days, again depending on thickness. It notes kiln-dried lumber is heated for hours to about 125 to 140 °F.

On fumigation it is blunt: an extreme and costly option, requiring occupants to leave for about three days, and it says sulfuryl fluoride fumigants are less effective against wood-boring beetles than the discontinued methyl bromide, so de-infestation may not be successful. It adds that furniture can be fumigated more effectively and at substantially lower cost than a building.

None of this is a home procedure. Heat and freezing treatments on furniture carry their own risks to joints, veneer and finishes, which is why the AIC instruction routes an infested piece to a conservator or a conservation-aware exterminator rather than to a chest freezer.

Why killing mold does not end the problem

This one surprises people, so it is worth restating from the leaflet. Deactivating mold and killing mold are different things: extreme cold, freezing and heat deactivate spores but do not kill them, and warming reactivates them. And even where mold is genuinely inactive, the leaflet says that killing mold does not eliminate all health hazards and that inactive mold may cause allergic reactions in sensitive people.

So "I put it in the garage over winter and the mold died" is not a conclusion the source supports. What the source supports is controlling moisture, isolating affected objects in polyethylene, not touching the mold, and getting advice. The deactivation options it lists, including air drying at 86 to 104 °F, it frames as things to consider in consultation rather than as a home procedure.

8. See it: the Ferris chest stays outside See it

Fictional example

The Ferris family's painted pine chest, out of a relative's barn, in November.

The pass, done on the driveway:

Holes and powder. About 25 round holes, roughly 1/16 inch, over an area about 8 by 10 inches in one end panel. Pale powder on the ground underneath, the color of freshly sawed wood. Swept it away, marked the holes with a pencil circle, wrote the date.

Smell. The inside smells of barn rather than of must. No visible mold.

Seams and folds. None: no upholstery.

Paint. Painted, chipping over roughly a third of the end panel. The family believes the chest predates 1940, so the paint may predate 1978.

Decision: it does not come in.

Known: holes of a size that falls inside the ranges both extension sources give; pale powder present on the day; chipping paint on a piece that is probably pre-1978.

Assumed, and it is the family's assumption: that the powder is fresh frass rather than old frass dislodged when the chest was moved out of the barn. That assumption is exactly the one Kentucky's fact sheet warns about, and sweeping and rechecking is the test. Because it is November, and the same fact sheet says emergence is mostly spring or summer, the recheck is scheduled for spring and the report says the winter reading will be inconclusive.

Still open: the beetle family, which decides whether re-infestation is likely. Under the published figures the hole size is consistent with more than one family, and the two sources disagree about which, so this is a question for an extension entomologist or a licensed pest control operator who can look at the wood. And whether the paint contains lead, which nobody present can establish by looking, and which EPA's own position on home test kits means a hardware-store kit will not settle either.

What the family does, under those assumptions: the chest stays in the open-sided woodshed, off the ground, bagged if it has to be moved. The plan sheet's only row reads "nothing yet, deciding later, recheck swept area in spring." Nobody sands anything.

Why this is a success rather than a failure: twenty minutes on a driveway kept a possibly active infestation and a possibly lead-painted surface out of a house with children in it, and cost nothing but the chest's comfort over a winter.

The sources behind this chapter, all read for Learn Furniture Care on 13 November 2026:

9. Practice: the twenty-minute pass Practice

Minimum: one piece, outdoors, every line of the hazards sheet ticked, and a decision. Time: about 20 minutes. Materials: a flashlight, a pencil, a ruler, a phone camera, a dust mask if the piece is dusty, and your condition report open on the hazards sheet.

  1. Work outdoors or in a garage, with the piece off the ground if you can manage it.
  2. Light along every surface, end grain included, looking for small round holes. Measure any you find and count them.
  3. Look underneath for powder, note its color, sweep it away, mark the holes and write the date.
  4. Open everything and smell it. Drawers, cupboards, the inside of a lid.
  5. Look into any upholstery seams and folds with the light, for the signs the CDC page names.
  6. Decide the paint question and note any chipping and its area.
  7. Tick every line and write the decision: clear, isolate it, it does not come in, or ask someone.
Go deeper

The recheck. This is the half of the pest test people most often skip, and it is the half that decides. Put a reminder in your calendar for the swept area, four to eight weeks out and inside spring or summer if the first check was in autumn or winter. When it comes round, look at the same spot with the same light, photograph it, and write a second dated line. Two dated readings turn "there are holes" into "active" or "old," and no single visit can do that.

10. Your piece Your piece

11. Check your work Check your work

Criteria

  • Was the pass done before the piece came indoors, or is it recorded why that was impossible?
  • Is every line of the hazards sheet ticked, including the lines you were confident about?
  • If there are holes, is the powder's color recorded, the sweep dated, and a recheck date set?
  • If the recheck falls outside spring or summer, does the report say the reading may be inconclusive?
  • Is the paint question answered, with the chipping area noted if any?
  • Is there an explicit decision for the piece: clear, isolate it, it does not come in, or ask someone?
  • Did you decide where the solvent rags go before opening any solvent?

Worked example

The Ferris pass ticks every line, records the powder's color and the sweep date, sets the recheck for spring and says why a winter reading would be inconclusive, answers the paint question and notes the chipping area, and ends with an explicit decision. Checked against the criteria it passes on every one. Its most valuable feature is the last: a decision that the chest does not come in, recorded on the day, which is the output the whole pass exists to produce.

Common mistakes

  • Doing the pass indoors because the weather was bad. The findings then have nowhere to go.
  • Treating holes as the finding. The powder, its color, and whether it comes back are the finding.
  • Doing one look instead of two. Active and old are distinguished by sweeping, dating and rechecking.
  • Rechecking in November and concluding "inactive." Emergence is mostly spring and summer.
  • Naming a beetle family from the hole size. The two extension sources disagree, so the size gets you to a group at best.
  • Trusting a hardware-store lead test kit. EPA's page says CPSC does not recommend them for consumer products.
  • Assuming a dry piece has no mold problem. Spores lie dormant without moisture and reactivate when conditions change.
  • Leaving solvent rags in a wastebasket. Flat, single layer, on concrete, outdoors, corners weighted.

What is still unresolved

This chapter recognizes hazards; it does not treat them. Identification of a beetle family, fumigation, mold remediation, lead paint removal and stripping are all outside it, and Who to hire for furniture work is where each of them goes. The regulatory position in section 5 is dated and is live litigation, so check the EPA pages themselves if it matters to your decision. And nothing here says whether a piece is worth treating, which is What not to do to old furniture, and why and, where money is involved, an appraiser.

12. Knowledge check and scenario

You find twenty small holes and some pale powder. What is the test, and what is the trap?
The test is to note the powder's color, sweep it all away, mark the holes and look again later: fresh powder the color of freshly sawed wood suggests activity, while yellowed or caked powder suggests old damage. The trap is twofold. Vibration from moving the piece can dislodge old powder, which looks like activity; and emergence is mostly spring or summer, so a recheck in autumn or winter may show nothing and prove nothing.
A piece was in a damp basement, smelled musty, and has been in a dry garage for a year. Is the mold problem over?
Not on the evidence of drying alone. The Park Service's leaflet says spores lie dormant without moisture rather than dying, that cold and heat deactivate spores without killing them, and that killing mold does not eliminate all health hazards, with inactive mold still causing reactions in sensitive people. Dry storage has stopped growth, which is worth a lot, and it has not settled the health question.
Why does Learn Furniture Care not teach stripping, even for a piece where refinishing is a reasonable choice?
Three reasons stack up. The conservation literature treats removing a finish as a last resort and it is irreversible by definition. The paint on an older piece may contain lead, and EPA's instruction is not to attempt to remove lead-based paint yourself. And the consumer stripper chemistry is unsettled: the 2019 methylene chloride consumer rule stands, the broader 2024 rule was vacated in September 2026, and the common substitute is subject to a proposal that has not been finalized.
(Go deeper) Why do holes appear in a varnished tabletop if finished surfaces are immune to egg-laying?
Because the eggs were not laid there. The Kentucky fact sheet says surfaces that are stained, varnished, waxed or painted are immune from attack, meaning eggs are laid into unfinished wood, and that larvae already inside emerge through whatever is on the surface. So holes in a finished top usually mean the infestation began in unfinished wood, often the underside or the inside of the piece, or was present in the timber before it was made up. It also explains why borate surface sprays, which do not penetrate a finish, are of little use on a finished piece.
A neighbor offers you a painted blanket chest from their garage. It is free, you have a van today, and there are a few small holes in one end. Your youngest is three. What do you do?
This is a reasonable compromise and much better than carrying it indoors. The pass still happens before the house, which is the main thing. What it costs you is that a piece with a possibly active infestation spends a week in your garage next to whatever else is in there, and that a decision to decline becomes a decision to dispose of something you now own.
The pass is twenty minutes and it is at its most useful before the piece is yours. If the powder is fresh you can decline, or agree to leave it where it is while the recheck runs, and either way the question is settled where the answer can still change what happens. With a three-year-old in the house the paint question also wants answering before the chest arrives, not after.
This is the course of action this chapter exists to prevent. Paint on a chest that old may contain lead, EPA's instruction is not to attempt to remove lead-based paint yourself, and its page lists refinishing old furniture among the activities that may increase lead exposure. Doing it outdoors reduces one exposure route and leaves the others, including dust on clothing in a house with a small child. It would also destroy the evidence the pass is for.

Checklist

Records your learning only; it is not a qualification.

The chapters in this book are also published at Learn Furniture Care, Learn Art Framing and Learn Machine Sewing, where the tools and record sheets they mention are kept.