That leaves what is worth doing yourself, and the list is short on purpose. A loose chair joint, a drawer that drags, a pull that has worked free: each one is reversible, each can be finished in an evening, and each has a single step that decides whether it holds or comes apart again by spring.
The furniture repairs worth doing yourself
A short list: a loose joint, a dragging drawer, a loose pull, a detached glue block. A shorter list of what is not on it, with the reason, and the step everybody skips.
- Start here: the essentials
- 1. What is on the list, and what is not
- 2. Willing joints
- 3. This is the step people skip
- 4. Choosing a glue, from the makers' own figures
- 5. The dry run
- 6. Gluing up
- 7. The small repairs
- 8. See it: Marcus's two chairs
- 9. Practice: one joint, start to finish
- 10. Your piece
- 11. Check your work
- 12. Knowledge check and scenario
Start here Essentials
At minimum: check the repair is on the list, take the joint apart only if it comes willingly, clean off every trace of old glue, dry-run it, then glue up. The glue comparison and the dowel work are Go deeper.
- Check the repair is on the list. If not, this chapter sends you to Who to hire for furniture work (section 1).
- Take the joint apart only if it comes apart willingly. A joint that resists is telling you something (section 2).
- Get every trace of the old glue off. This is the step people skip and it is why repairs fail (section 3).
- Dry-fit and clamp with nothing in the joint, and time it. Then budget the assembly with Planning a glue-up (section 5).
- Glue up, then write down what you used. The glue in a joint is what the next repairer inherits (your condition report).
Minimum time: about two hours spread over two days for one joint, most of it waiting. Done when: the joint is tight, the squeeze-out is cleaned off, and your report names the glue you used and the date.
1. What is on the list, and what is not Understand
Learn Furniture Care teaches a short list of repairs. The list is short for a reason that is worth stating: the one genuinely technical paid course in Learn Furniture Care’s comparison spends eight modules and four chair projects on regluing chairs, and that whole course is about joints that are loose rather than members that are broken. Doing one repair properly is a substantial subject.
| On the list | Not on the list | Why not, and where it goes |
|---|---|---|
| A loose joint, reglued after the old glue is removed | Any break across the grain in a member that carries a person | It fails suddenly and the piece stops being used today. Joints, racking and breaks sets the line; Who to hire takes it from there |
| A chair that racks but has no break | Dowels broken off inside a mortise | Removing a broken dowel without enlarging the hole is the skill the whole repair turns on. See Go deeper for what is involved |
| A sticking or dragging drawer | Veneer losses that need patching | Matching a patch to surrounding veneer is skilled work in a specialty that covers veneer and marquetry |
| A loose or missing pull or knob | Inlay and marquetry | The decorative surface and the groundwork under it are both specialist work |
| A wobble that is the floor rather than the joints | Anything on a painted or gilded surface | The cleaning guidance stops at dusting on painted surfaces unless you are trained, and the paint may be a hazard: see What can hurt you in old furniture |
| A detached molding or glue block, where the part is present | Anything on a piece whose value has not been settled | Order matters and it does not reverse: What not to do to old furniture, and why |
| Recording what you did, which is a repair in its own right | Re-adhering lifted veneer | See the Limits box below |
Lifted veneer is on the decision list and not on the doing list. A small lifted edge is exactly the kind of fault an owner can identify, record and protect, and Learn Furniture Care does not publish a method for gluing one back down, because the research behind it found no source for that method meeting the standard the rest of Learn Furniture Care is held to.
What you can do, and it is worth doing: establish lifted rather than lost by pressing along the edge, record the area, keep cloths and dusting away from that edge, since the cleaning guidance warns specifically about snagging raised edges on veneered and inlaid surfaces, and if a fragment has come away, bag it and label it with its original location on the piece, which is the conservation guidance's own instruction for a detached element. Then the re-adhesion goes to somebody whose specialty covers it.
The same applies to adhesives Learn Furniture Care has no guidance for. It found no citable source on when epoxy or cyanoacrylate is or is not appropriate in furniture repair, so it recommends neither, and What to use, and what not to carries that limit on its own page.
2. Willing joints
A reglue starts with taking the joint apart, and whether it will come apart is the question that decides whether this is your repair.
A willing joint moves when you work it gently, opens progressively, and comes apart with hand pressure or with light persuasion. Its glue line has already failed; you are separating parts that are no longer stuck.
An unwilling joint resists. And a joint that resists is telling you one of several things, none of which is "push harder": that it is not as loose as it appeared, that a screw or nail is holding it, that there is a dowel or a pin you have not seen, or that the looseness you felt is actually a crack somewhere else being read as joint movement.
So the rule for this chapter: work a joint gently, and if it does not come, stop and look again. Forcing an unwilling joint is how a loose joint becomes a broken tenon, and a broken tenon is not on the list.
Before any of this, go back over the previous-repair survey from Joints, racking and breaks. Screws driven through a joint and filled over, brackets, nails: any of these will stop a joint opening and will damage the parts if you pull against them. Find them first.
Convention Work in order, and mark as you go. Label each part and its position before anything comes apart, photograph the assembly from two angles, and note which way round each piece sat. Furniture parts that look symmetrical frequently are not, and a chair reassembled with two side rails swapped will not come square.
3. This is the step people skip
If you take one thing from this chapter, take this. The step that decides whether a reglue holds is not the gluing; it is what happens to the old glue first.
Old Brown Glue, a liquid hide glue manufacturer, states the requirement plainly in its own FAQ. If the old glue is modern glue, it says, you need to remove it completely to the bare wood. If it is hide glue, it says bare wood is preferable, and adds that hide glue is the only glue that bonds to itself, so it will bond to old hide glue if you reactivate that with moisture.
Product-specific That is a manufacturer speaking about its own product category, and it is worth reading as such. What it establishes for your purposes is the asymmetry: with modern glue there is no bonding to the old layer, so the old layer has to go. A joint reglued over a skin of cured PVA has glue bonded to glue rather than to wood, and that is the common reason a reglued chair is loose again within a year.
What this means in practice is that cleaning the joint takes longer than the glue-up, and that a surface which looks clean is often not. Old glue sits in the pores and in the corners of a mortise where fingers do not reach. Work on both halves, check by feel as well as by eye, and keep going until the wood feels like wood.
Two cautions about how you clean it. Taking wood off along with the glue makes the joint slacker than it was, which creates the problem you are trying to fix, so the aim is to remove the glue and stop. And if you wet the joint to soften old glue, give it time to dry fully before gluing, because glue of any kind goes onto dry wood.
4. Choosing a glue, from the makers' own figures
Every figure in this section is a manufacturer's own published product data, not an independent test, and that is how it should be read.
| Glue | Minimum application temperature | Open assembly | Total assembly | Maker's own notes |
|---|---|---|---|---|
| Titebond Original | Above 50 °F | 4 to 6 minutes | 10 to 15 minutes | Not intended for exterior use or where moisture is likely; not for structural or load bearing applications |
| Titebond III | Above 47 °F on the data line; the limitations text says above 45 °F | 8 to 10 minutes | 20 to 25 minutes | Not for continuous submersion; not for structural or load bearing applications |
| Titebond Genuine Hide Glue | Above 50 °F | 10 minutes | 20 to 30 minutes | Its sensitivity to moisture "allows for easy disassembly of parts," which the maker calls a critical benefit in antique restoration |
| Hot hide glue | A glue temperature of 110 to 160 °F, with about 140 °F named best, and a caution not to exceed 180 °F for any length of time | No open or total assembly time published on the source page | Old Brown Glue's figures. Clamps for hours for hot hide glue, overnight for its liquid product | |
Four things to notice, because they change how you plan a job.
All three Titebond figures are stated at 70 °F and 50 percent relative humidity. A cold garage in February is not that, and the makers publish no correction for it. What they do publish is a minimum application temperature, which is the line that tells you whether to do the job today.
Titebond's own page for Titebond III gives two different minimums. The application guidelines say above 47 °F and the limitations text says above 45 °F. Learn Furniture Care reports both rather than picking one, and so does Planning a glue-up.
All three Titebond products carry the same published clamping pressures: generally 100 to 150 psi for softwoods, 125 to 175 psi for medium woods and 175 to 250 psi for hardwoods. The calculator turns that into a force for your joint face.
None of these pages publishes a clamping time or a full cure time. Learn Furniture Care therefore states none. Old Brown Glue does give clamping guidance for its own products, overnight for the liquid and hours for hot hide glue, and that is a different manufacturer speaking about a different product.
The reversibility question
Hide glue is often described as reversible, and the manufacturers make that claim themselves. It is worth stating with the qualification the maker attaches to it.
Old Brown Glue says reversing a hide glue bond takes a combination of both heat and moisture, and that simply adding dry heat is not enough in most cases. For a fully cured joint, it says it is necessary to add water to hydrate the protein first and then add heat. Titebond's hide glue page says its sensitivity to moisture allows for easy disassembly of parts, which it calls a critical benefit in antique restoration.
Physical principle So the honest form is: hide glue can be reversed under conditions a later repairer can arrange, and reversing it is not a matter of waving a hairdryer at it. The practical consequence is about the next person rather than about you. A joint glued with PVA is a decision somebody in thirty years cannot easily undo. That is a reason to think about which glue you use, not a prohibition on using the one you have.
5. The dry run
Assemble the whole joint, or the whole chair, with nothing in the joint, clamp it exactly as you intend to, and time yourself. Then take it apart again.
This is the step that converts the makers' published figures into your reality, and it is the one that reveals the problems while they are still free to fix. What the dry run finds: that a clamp does not reach; that a part goes in only at one angle; that the assembly does not pull square; that you need a third hand; that the clamp pads mark the wood; and, most often, that the whole thing takes longer than you thought.
Time it, because the time is the constraint. Planning a glue-up takes the maker's total assembly time and divides it by the number of joints you mean to do at once, and the arithmetic is sobering: a chair with sixteen joints glued in one go, with Titebond Original's published total assembly time of 10 to 15 minutes, leaves roughly 37 to 56 seconds per joint. That is why furniture is often glued up in stages rather than all at once, and the dry run is where you decide what the stages are.
Prepare before any glue is opened: clamps set to roughly the right opening, cauls and pads to hand, a damp cloth ready for squeeze-out, the parts laid out in order, and a square or a tape to check the assembly. Convention Checking that an assembly is square while the glue is still open is a chance you get once.
6. Gluing up
With the joint cleaned to bare wood, dry, and dry-run, the glue-up itself is quick.
- Check the room temperature against the maker's minimum for the glue you are using. If the room is below it, the answer is to move the work or wait, rather than to go ahead.
- Apply glue to both surfaces of the joint in a thin even film. More glue does not make a stronger joint; it makes more squeeze-out.
- Assemble within the open assembly time, and have the whole thing together within the total assembly time. These are the two figures from the table.
- Clamp to bring the joint tightly together. The makers' published range is 100 to 150 psi for softwoods, 125 to 175 for medium woods and 175 to 250 for hardwoods, and Planning a glue-up converts that to pounds on your joint face.
- Check square immediately, and adjust while the glue is still open.
- Deal with the squeeze-out while it is manageable. Glue left on a surface will show when any finish goes over it.
- Leave it clamped. None of the Titebond pages publishes a clamping time, so Learn Furniture Care states none; follow the instructions on the container you bought.
- Write it down. Date, which glue, which joints, on the What was done sheet in your condition report.
On clamping pressure, a note on what the published range is and is not. It is a specification for the pressure at the glue line. Learn Furniture Care has no sourced figure for how much force a given clamp delivers, so the calculator reports the force the range calls for and stops there. What the number is good for is sanity: it tells you whether you need two clamps or six, and it tells you that hand pressure alone is not in the range.
7. The small repairs
These are the jobs that need no glue-up and are worth doing properly.
A wobble that is the floor
Established in Joints, racking and breaks by moving the piece and turning it. If the wobble stays behind, it is the floor and the piece needs nothing. If it moves with the piece and the joints are tight, one foot is short or worn. Find which by pressing each corner in turn and seeing which one rocks, and deal with it by leveling that foot rather than by tightening joints that are not loose.
A dragging or sticking drawer
Work out which of three things it is before doing anything. The drawer may be rubbing where the runners and the drawer sides have worn, which shows as polished or scored tracks. The case may have racked, which shows as a drawer that binds in one corner and is free in the opposite one. Or the wood may have swollen seasonally, which shows as a drawer that was fine in February and sticks in August.
Test it That last one is worth checking before any wood is removed, and Humidity and movement is how: a drawer that sticks only in the humid half of the year is a piece responding to its room, and taking material off it in August gives you a loose drawer in February. Keeping furniture from getting worse is the chapter for that problem.
If it is wear, the repair is to the runner rather than to the drawer wherever possible, because the runner is the sacrificial part and is easier to replace. Where the drawer sides themselves are worn into a curve, that is a repair worth a quote rather than a weekend.
A loose or missing pull
Loose pulls are usually loose fixings rather than loose pulls. Take it off, look at the hole, and see whether the fixing is stripped, whether the hole has become oval, or whether the fixing is simply short. Record what you find, because an oval hole in a drawer front is a small structural finding rather than a hardware one.
If a pull is missing, resist the urge to replace the whole set to match. Original hardware carries information, as Surfaces, veneer and hardware sets out, and a set replaced to make one drawer match removes it from every drawer. If you do change hardware, keep the originals in a labeled bag with the piece.
A detached molding or glue block
Where the part is present and the location is certain, this is on the list. Where the part is present and the location is uncertain, follow the conservation instruction first: bag it and label it with its original location, or in this case with your best record of where it came from, including a photograph of the empty space. Where the part is missing, replacing it is a judgment about adding new material to the piece, which belongs on the plan sheet as a decision rather than being done because the gap is annoying.
Hide glue or PVA, as a decision the next repairer inherits
The published figures sit side by side in section 4; here is what they mean for a choice.
PVA, the Titebond products among them, is widely available, forgiving, strong and well documented, and the makers' own limitation lines say it is not for structural or load bearing applications, which is worth reading twice given what people glue with it. Its practical drawback for old furniture is that a cured PVA joint has to be cleaned back to bare wood before it can be reglued, which is the requirement in section 3, and that cleaning is the labor in any future repair.
Hide glue, liquid or hot, is what much old furniture was made with, bonds to itself when reactivated with moisture, and is described by its makers as reversible with a combination of heat and moisture. Its drawbacks are a shorter history in most readers' hands, temperature requirements in the case of hot hide glue, and the fact that its moisture sensitivity, which is the feature, is also a vulnerability in a damp room.
The way to make the decision is to ask who the next repairer is working for. On a piece likely to be repaired again, and on anything where the value question is unsettled, the reversible option is doing somebody a favor. On a kitchen chair that will be used until it is thrown away, the convenient option is a reasonable choice and Learn Furniture Care does not moralize about it. What matters in both cases is that the choice is recorded, because the next person cannot tell by looking.
Why clamping pressure has a published range
The range exists because the pressure needed to bring a joint tightly together without crushing the wood depends on the wood. Softer woods compress at lower pressures, so the published range for them is lower; hardwoods need more pressure to close the joint and tolerate more before the fibers crush. That is why the makers give three bands rather than one number.
What over-clamping does, in the direction the range is warning about, is crush the wood fibers at the glue line and starve the joint of glue by squeezing too much out. What under-clamping does is leave a gap, and a glue line that bridges a gap is weaker than one between two closed surfaces. Both failure modes argue for the same discipline, which is a dry run that shows you the joint closes properly without force.
Removing a broken dowel
This is off the list and it is worth knowing why, since it is the single most common reason a straightforward-looking chair repair becomes somebody else's job.
When a dowelled joint fails, the dowel often snaps, leaving part of it glued inside one of the two holes. The repair requires getting that remnant out without enlarging the hole or splitting the surrounding wood, and then restoring a hole that will take a new dowel of the right diameter at the right angle. Doing it by drilling requires the drill to stay exactly on the original axis in material that is harder in one direction than the other. The paid course Learn Furniture Care cites treats removing broken dowels as a module of its own, alongside disassembly, glue cleaning and glue-up, which is a reasonable indication of its standing as a skill.
If your dry run reveals a broken dowel, the useful response is to stop, photograph it, and add it to the inquiry you send under Who to hire for furniture work.
The sequence a whole course gives a chair
For scale, the published outline of the one technical course in Learn Furniture Care’s comparison runs: chairs, glue and tools; disassembling a formal chair; preparing the parts, which includes cleaning glue residue from joints and removing broken dowels; gluing up; utility chairs; upholstered seats; flat-pack chairs; and a summary. Eight modules, sixteen videos, eight exercises and four chair projects the learner sources themselves.
That is not an argument against attempting a reglue. It is an argument for attempting your first one on the least precious thing you own, and for expecting the cleaning step to take most of the time.
8. See it: Marcus's two chairs See it
Marcus's chairs one and two. Both rack about half an inch at the top of the back, springing back, with a creak from the rear joints. No cracks found in the joint-by-joint walk. Chair four, with the cross-grain line in a rear seat rail, is out of use and out of this chapter.
Checking the list. Loose joints, no breaks, a piece whose value question Marcus answered as "probably nothing special" with his reasoning written down. On the list.
The previous-repair survey, redone before touching anything. One screw through the rear left joint of chair one, driven at an angle from underneath and not filled. Marcus photographs it and removes it before trying the joint.
Willing or not. Chair one's rear joints open with gentle working, progressively. Chair two's left rear joint comes; the right rear does not move. He stops on that one and looks again, and finds a second screw he had missed, under a drip of old finish.
The cleaning, which took the afternoon. The old glue is brittle and dark. He works both halves of every joint back to bare wood, checking by feel. This takes about four times as long as he expected and is the only part of the job he would describe as difficult.
The dry run. He assembles chair one dry with the clamps he owns. Two findings: he is one clamp short for the back, and the chair does not pull square unless the side rails go in before the back. He borrows a clamp and writes the order down.
The arithmetic. Eight joints per chair. Using Titebond Original's published total assembly time of 10 to 15 minutes, Planning a glue-up gives him roughly 75 to 112 seconds per joint if he does a whole chair in one go. His garage is 55 °F, which is above the maker's published minimum of 50 °F, so the job can go ahead. He decides to do one chair per session rather than both.
Known: which joints were loose, that no member is broken, the screw locations, the assembly order, the room temperature and the published figures.
Assumed: that the old glue was a modern adhesive rather than hide glue, from its appearance and brittleness. Under that assumption the requirement is to clean back to bare wood, which he did, and which is also the safer assumption if he is wrong.
Still open: whether chair four is repairable, which is somebody else's assessment, and whether the gummy surface on all four is silicone, which the cleaning chapter explains is recorded as suspected rather than established.
What went on the report: date; "chairs 1 and 2, eight joints each, disassembled, old glue removed to bare wood, reglued with Titebond Original, clamped overnight per container, squeeze-out cleaned. Two screws removed from previous repairs, locations photographed. Garage 55 °F at time of work."
Why that last line matters: in ten years, somebody taking these joints apart will know what is in them, and that it is a modern PVA that will have to come back to bare wood again.
The published figures and the curriculum outline behind this chapter:
- Old Brown Glue FAQ (a liquid hide glue manufacturer): the requirement to remove modern glue completely to bare wood, hide glue bonding to itself, the working temperatures, and the heat-and-moisture qualification on reversibility.
- Titebond Original, Titebond III and Titebond Genuine Hide Glue (Franklin International): the application temperatures, assembly times, clamping pressure ranges and limitation statements in section 4, each the maker's own published data.
- Introduction to Furniture Repair (Fixing Furniture, a paid course listed as a reference rather than a recommendation): its published outline, which is the evidence for how much work a chair reglue is and for removing broken dowels being a subject of its own.
- Caring for Your Treasures (American Institute for Conservation): the instruction to bag a detached element labeled with its original location.
9. Practice: one joint, start to finish Practice
Minimum: one loose joint on the least precious piece you own, taken apart, cleaned to bare wood, dry-run and reglued. Time: about two hours of work spread over two days, most of it waiting. Materials: clamps and pads, a glue whose published figures you have read, something to clean old glue with that does not remove wood, a damp cloth, a square, labels and a camera.
- Check it is on the list, and check the value question is settled or reasoned.
- Redo the previous-repair survey and remove any fixings before trying the joint.
- Label and photograph every part and its orientation before anything comes apart.
- Work the joint gently. If it resists, stop and look for what is holding it.
- Clean both halves back to bare wood, and expect this to take most of the session. Let it dry fully if you used any moisture.
- Dry-run the whole assembly with clamps, time it, fix what the dry run reveals, and write down the order of assembly.
- Check the room against the maker's minimum temperature, then glue up within the published assembly times.
- Check square, clean the squeeze-out, leave it clamped per the container.
- Write it on the What was done sheet: date, glue, joints, and anything you found.
The timed rehearsal. Do the dry run twice, the second time with a timer running and a tube of hand lotion standing in for the glue, applying it to every joint face as you would the real thing. Two things come out of it. You find out what your actual assembly time is, as against the maker's figure, which includes the fumbling and the clamp that slips. And you find out whether your plan fits inside the published total assembly time, which is the number that decides whether you do a whole chair at once or in stages. Twenty minutes, and it is the difference between a calm glue-up and the one everybody remembers.
10. Your piece Your piece
11. Check your work Check your work
Criteria
- Was the repair on the list, and was the value question settled or reasoned before you started?
- Did you find and remove previous fixings before trying the joint?
- Did every joint come apart willingly, and did you stop on any that did not?
- Is the old glue off, back to bare wood on both halves, checked by feel as well as by eye?
- Did you dry-run with clamps and time it before opening any glue?
- Was the room at or above the maker's published minimum temperature?
- Is the joint tight, square, and the squeeze-out cleaned off?
- Does the report name the glue, the joints and the date?
Worked example
Marcus's record names the chairs, the number of joints, what was removed, what went in, the clamping, the previous repairs found, and the room temperature at the time of work. Checked against the criteria it passes on all eight. The two details that make it a good record rather than a note are the temperature, which tells a later reader the published figures applied, and the named glue, which tells them the joint will need cleaning back to bare wood next time.
Common mistakes
- Adding glue to a loose joint without taking it apart. The glue bonds to old glue rather than to wood, which is the requirement in section 3 and the usual reason a reglue fails.
- Forcing an unwilling joint. A loose joint becomes a broken tenon, which is off the list.
- Missing a screw from a previous repair. Redo the survey before pulling anything.
- Not labeling the parts. Symmetrical-looking parts usually are not.
- Skipping the dry run. It is free and it finds the problems while they are still free.
- Gluing too many joints at once. The published total assembly time divided by the joint count is the number that decides this.
- Working below the maker's minimum temperature. The figure is on the page for a reason.
- Too much glue. It makes squeeze-out rather than strength.
- Leaving squeeze-out to deal with later. It shows under any finish.
- Not recording what you used. The next repairer cannot tell by looking.
What is still unresolved
This chapter does not repair broken members, remove broken dowels, patch veneer losses, re-adhere lifted veneer or touch inlay, marquetry, paint or gilding, and it recommends neither epoxy nor cyanoacrylate because it found no citable guidance on either. Each of those goes to Who to hire for furniture work. It also does not say whether a repair is worth what it costs, because Learn Furniture Care does not know what anything costs.
12. Knowledge check and scenario
Why does adding glue to a loose joint without taking it apart usually fail?
Your garage is 46 °F and you have Titebond III. What do the maker's figures say?
A drawer sticks in August and runs freely in February. What is the repair?
(Go deeper) Why is a broken dowel inside a mortise off Learn Furniture Care’s list?
Checklist
Have you just done what Learn Furniture Care teaches? If it is still fresh, we would like to hear about it. We are looking for volunteer guides to add a few short passages from their own experience to Learn Furniture Care. Write to guides@learnthings.online for the details.
The chapters in this book are also published at Learn Furniture Care, Learn Art Framing and Learn Machine Sewing, where the tools and record sheets they mention are kept.